Kampek
040-502 9474
FIEN
Request quote →
KMP-0001 to KMP-0005

Technical drawings

Kampek's own drawings. Each asserts only what is already published on this site or on the manufacturer's own pages, and each carries a number you can cite in a quote or a tender.

Request quote →040-502 9474
KMP-0001

The edges anchor, the centre seals.

KMP-0001. Longitudinal section through a joint: hot-melt at the edges, a visco-elastic mastic in the centre.

Go to the product →

RJS-E heat-shrink sleeve, longitudinal section through a field jointSection through a field joint. A steel carrier pipe at the bottom, PUR insulation and a PE casing above it. The heat-shrink sleeve is wrapped over the joint, with a cross-linked polyethylene backing. Two different adhesives sit on its underside: a hot-melt along both edges and a visco-elastic mastic down the centre.Joint12345KMP-0001
  1. 1Cross‑linked PE backing
  2. 2Hot‑melt adhesive, along both edges
  3. 3Visco‑elastic mastic, centre
  4. 4PE casing
  5. 5PUR insulation and steel pipe
KMP-0002

The closure

KMP-0002. A wrap-around sleeve leaves a longitudinal overlap. The WPCP‑IV closure patch seals it, built the same way as the sleeve itself.

Go to the product →

WPCP‑IV closure patch, transverse section at the sleeve overlapSection taken around the pipe. The casing sits in the centre with the wrap‑around heat‑shrink sleeve around it. The ends of the sleeve overlap at the top and form a longitudinal seam. The WPCP‑IV closure patch is applied over that seam, and uses the same cross‑linked HDPE backing and the same adhesive construction as the sleeve itself.Width 100 or 150 mm12345KMP-0002
  1. 1PE casing
  2. 2Wrap‑around heat‑shrink sleeve: backing and adhesive
  3. 3Longitudinal overlap of the sleeve
  4. 4WPCP‑IV closure patch over the seam
  5. 5Same cross‑linked HDPE backing and adhesive as the sleeve
KMP-0003

The type-tested constructions

KMP-0003. Three constructions to EN 489-1:2019. The drawing carries no diameter: the type test covers casing sizes Dc 250 and 160 mm.

Go to the product →

BG Industry's three type-tested joint constructionsThree longitudinal sections side by side. On the left the basic PE sleeve, sealed with butyl mastic at both ends and foamed on site. In the middle the PEX sleeve, where the insulation is made with pre‑fabricated shells instead of foaming in the joint. On the right the welded sleeve, which adds a circumferential electric weld at both ends to the butyl seal.PE sleevePEX sleeve · 2.1Welded · 4.112345KMP-0003
  1. 1Shrink sleeve, casing‑grade HDPE PE 100
  2. 2Butyl seal at both ends of the sleeve
  3. 3Foamed in the joint on site
  4. 4Pre‑fabricated insulation shells instead of foaming
  5. 5Circumferential electric weld in addition to the butyl seal
KMP-0004

The compound flows into the pores of the surface.

KMP-0004. Magnified section through the pipe wall: steel, compound, mechanical overwrap. No primer.

Go to the product →

Stopaq layer build-up on a steel pipe, magnified wall sectionMagnified section through the wall of a steel pipe. At the bottom the steel, cleaned by wire brushing to ST 2, so the surface stays irregular and not all rust has been removed. Above it the visco‑elastic polyisobutene compound, which flows into those irregularities and fills them completely. On top, a mechanical PE overwrap. There is no primer between the layers.No primer, no blastingMagnified12345KMP-0004
  1. 1Steel pipe, wire‑brushed to ST 2
  2. 2Surface irregularities the compound flows into
  3. 3Visco‑elastic polyisobutene (PIB) compound, cold‑applied
  4. 4Mechanical overwrap, for example Outerwrap
  5. 5The compound never dries or cures, so it self‑heals small damage
KMP-0005

The termination

KMP-0005. At a line termination the casing and insulation stop. The DHEC end cap closes the insulation space against the carrier pipe.

Go to the product →

DHEC end cap, longitudinal section through the termination of a pre-insulated lineSection through a line termination. On the left the pre‑insulated pipe: steel carrier pipe, PUR insulation and PE casing. On the right the carrier pipe continues uninsulated. The casing and the insulation stop, which would leave the insulation space open. The DHEC end cap is shrunk down from the casing onto the carrier pipe and closes that space, so water cannot reach the insulation.Pre‑insulated pipeUninsulated pipe12345KMP-0005
  1. 1PE casing
  2. 2PUR insulation
  3. 3DHEC end cap, casing down to carrier pipe
  4. 4The cap seals down onto the carrier pipe
  5. 5Carrier pipe continues uninsulated

Need dimensions or order codes?

The catalogue holds 172 order codes. Take the code from a row and it carries straight into the quote request.

Product catalogue →040-502 9474
CallRequest quote →